Installing Python Matplotlib On MacOS Sierra

I recently 'upgraded' to MacOS Sierra (Apple's latest Operating System) by doing a clean install. This resulted in a couple of challenges, including some software that could not be installed, and for which I had to find some alternatives.

Another issue I ran into is that some Python3 scripts with matplotlib wouldn't run, because matplotlib wouldn't install correctly.
I could 'pip' all I wanted, but the result was always:

$ pip3 install matplotlib
[...]
The following required packages can not be built: freetype

Some googling pointed me to some articles that freetype is/was a part of the XQuartz (X11) software that's no longer (pre)installed on MacOS Sierra. And in the past I have always upgraded my OS. The times that I did a clean install on this machine.... Must have been ages ago.

After some frustrating hours of trying to get this 'freetype' thing installed, I ran into an article on yantonov.com which solved my issue finally.

First I installed 'homebrew'.

$ /usr/bin/ruby -e "$(curl -fsSL https://raw.githubusercontent.com/Homebrew/install/master/install)"

After that I installed pkg-config and freetype:

$ brew install pkg-config
[...]

$ brew install freetype
[...]

And finally, I was able to successfully install matplotlib:

$ pip3 install matplotlib

Apple iOS Personal Hotspot Annoyances

This week, I ran into an annoying feature regarding the Apple iOS Personal Hotspot function of my iPhone 5s. I had to do some software testing with various WiFi clients. This worked fine, up to the moment that new devices ran into connectivity problems.

The new devices could connect, but got a message that there was no/limited Internet connectivity. Checking the IP address of the devices showed that they had an 169 address assigned.
So the iPhone wouldn't give new IP addresses to the new devices. Earlier devices that connected correctly could reconnect without a problem though.

It turned out to be a 'normal' DHCP problem. The IP address scope on the iPhone was depleted.

The iPhone has a small DHCP address pool that can give out 16 addresses (172.20.10.0-172.20.10.15). Of these 16 addresses are 3 taken by the network, broadcast (172.20.10.0 and 172.20.10.15) and iPhone itself (172.20.10.1). Leaving 13 addresses for other devices.

In normal situations, this shouldn't be a problem, but when your testing stuff, you can run into a shortage of IP addresses. Besides the shortage of addresses there is another challenge; no way of altering the DHCP lease time, or even clearing the issued IP addresses.

The lease time for the DHCP address is approximately 1 day (85536 seconds), as shown by a little network traffic capturing below.

20:53:29.544291 56:e4:3a:38:4d:64 > 00:23:6c:8d:7f:8e, ethertype IPv4 (0x0800), length 342: (tos 0x0, ttl 255, id 45806, offset 0, flags [none], proto UDP (17), length 328)
    172.20.10.1.67 > 172.20.10.2.68: BOOTP/DHCP, Reply, length 300, xid 0xfd7e0982, Flags [none]
      Your-IP 172.20.10.2
      Server-IP 172.20.10.1
      Client-Ethernet-Address 00:23:6c:8d:7f:8e
      sname "Free-Public-WiFi"
      Vendor-rfc1048 Extensions
        Magic Cookie 0x63825363
        DHCP-Message Option 53, length 1: ACK
        Server-ID Option 54, length 4: 172.20.10.1
        Lease-Time Option 51, length 4: 85536
        Subnet-Mask Option 1, length 4: 255.255.255.240
        Default-Gateway Option 3, length 4: 172.20.10.1
        Domain-Name-Server Option 6, length 4: 172.20.10.1

There is a function to reset the network settings on the iPhone, but that just clears everything regarding (wireless) network settings, but it doesn't touch the DHCP service in the iPhone. A reboot of the iPhone doesn't do the trick either. So you just have to wait till it clears automagically.

So there is room for improvement......