The last couple of years, we've had two ISP's on premise. One (XS4ALL) for basic Internet Access via VDSL, and one our (VoIP) phone provided by Ziggo.
The Ziggo phone services includes free (and ultra lite) Internet access
through the use of their cable modem. It's ultra-lite, since it's only
256kbps. More than enough for VoIP, but not nearly enough for modern
basic Internet access.
Posts tagged #Juniper
Create a Juniper SRX ca-profile For Unified Access Control
When you have a registered Juniper UAC / IC appliance, you have to option to download a VMWare version of the system. This is called a DTE appliance (Development and Test Environment). With this you have a full-blown UAC at your disposal for testing and development. Only downside is that it's limited to 5 connected users. Apart from that, it's just like the real-deal.
Juniper SRX Apply-groups
A while back I wrote a blog post about enabling global logging on security rules. This week I applied the same technique to enable ping on all zones for testing / troubleshooting purposes.
Instead
of adding ping as a host-inbound-traffic system-service to all zones,
and if you have a couple this means some configuring, you can solve this
by adding just 3 (three) lines of config to the firewall.
Configure Application Firewalling On A Juniper SRX
Juniper entered the realm of
application firewalling since the release of Junos 11.4 (for SRX
platforms). A realm that is mainly dominated by Palo Alto (they
basically invented it) and Checkpoint, but more and more vendor's are
starting to move in on that territory.
And Juniper is one of those vendors that started to implement Application Firewalling (AppFW) on their (SRX) firewalls.
Juniper SRX With DNS Proxy Service Enabled
Since the release of Junos v12.1x44D10 for branche SRX firewalls, Juniper added a feature called DNS-Proxy. This features enables the Junos device as a caching DNS server with several additional options. One of those feature is to define a Fully Qualified Domain Name (FQDN) with an IP address which overrides (if it exists) the entry in the 'official' DNS system on the Internet.
Public DMZ Access From Within The Network
This post basically describes the technique of how to deal with traffic originating from the inside of a firewall, and directing the traffic over the external interface IP address to a different internal zone.
First a network overview of the things used in this setup.Filter / Block IP Addresses On A Juniper SRX
While exploring the configuration options on the Juniper SRX firewall, I stumbled upon the so-called firewall filters. These filters are not to be mistaken for the firewall policy rules. They are something different, but can be used for achieving similar goals.
In my case, I wanted to see if it was possible to quickly block a list of IP addresses (or subnets) without the hassle of creating addressbook entries (Address Sets). My list of IP addresses consists of known hosts that participate in the criminal ZeuS network. These IP addresses are either Command&Control servers or servers used to transfer (captured) data to. In any case, servers you don't want to communicate with.
The solution on the SRX is to create a firewall filter containing the list with hosts / networks. The filter, in my case, is applied to the outgoing interface (fe-0/0/0).Enable Global (Security) Logging On SRX Policies
Normally, one would enable logging on each security policy. If you have hundreds of policies, and you want/need logging for troubleshooting, it takes a while (and some serious) effort to enable this for all policies.
Ziggo Internet, Juniper Firewalls and DHCP
At the house I have currently two ISP delivering broadband. Well, broadband isn't the correct word, since the the one of them is only a mere 256kbps (I think). The other is a 'whopping' 20Mbps.
The 20Mb connection is provided by XS4ALL, and the 256kbps is for free (if you have a phone subscription with Ziggo). The 256kbp is the minimum they provide to transport the phone calls, but if you're a masochist you can also browse the internet over that connection.
So, two ISP @ home. Combine that with a Juniper SRX firewall, and a dual ISP setup is born. The theory of that setup is that I connect both ISP's to the firewall, and use the 20Mb line as a default internet connection, but when that one dies, I automatically get switched to the backup line (256kbps).
Junos Pulse, Apple iOS, and Split-Tunneling
When you create (SSL)VPN access for you employees, you might enable split-tunneling to save corporate bandwidth. No split-tunneling means that all traffic is forwarded into the VPN tunnel. So if you browse the internet with an active VPN, the traffic goes through the VPN, and accesses the Internet through the corporate Internet connection. This isn't a big problem with a couple of employees, but with hundreds on the road or working from home, this might frustrate the employees in the building.